Holiday

Holiday DIY Projects

Holiday DIY Projects

Holiday Snowflake

Print Page
Banner
BDSquareLogo

BLACK+DECKER B+D Contributor 188 Projects

How to Make a DIY Holiday Snowflake

  1. Snowflake_step1

    Firstly, measure measure up 3 of your pieces of timber cut to a 800mm length.

  2. Clamp the timber securely into position and cut the 3 pieces to size.

  3. 9B6A2863

    Measure up and make a pencil mark in the center of each piece of timber. This is to create the grooves that will allow you to slot the 3 pieces together.

  4. 9B6A2868

    The timber we used was 45mm wide. We measured to cut two 15mm(d) x 40mm(w) grooves into opposite sides of the first piece of timber. In the other 2 pieces of timber, we measured to cut a 30mm(d) x 40mm(w) groove.

  5. 9B6A2900

    Use your jigsaw with a timber cutting blade to carefully cut out the grooves in each of the 3 pieces of timber.

  6. Snowflake_step3

    You now have the timber to create your snowflake frame. Your center piece looks like an ‘H’ and the other 2 pieces will fit either side of this.

  7. 9B6A2913

    Using a pencil and ruler, mark up cutting lines a the end of each piece of timber. This will give the pointed edges to your snowflake.

  8. 9B6A2945

    Set your jigsaw to bevel cutting mode, and carefully cut along the pencil lines. You now have the decorative, pointed ends to the snowflake frame.

  9. Snowflake_step4

    First place 1 piece of timber with a 30mm groove at the bottom with the groove facing upwards. Slot in the center piece, followed by the other piece of timber with the 30mm deep groove.

  10. Using your drill/driver, fix the pieces together with a screw.

  11. 9B6A2961

    Using a compass, draw a circle with a radius of 20mm. Then, keeping your compass at the exact same width, draw 6 dots at equal spacing around the edge of the circle. Connect the dots with straight pencil lines to create the star shape.

  12. 9B6A2967

    Using a piece of timber, draw another star inside the outline to create a border effect with the same width as your frame. This gives you your inner and outer cutting lines for the star.

  13. 9B6A2978

    Before you star to cut out the star, drill a hole within the insider border of the star to give you an easier start for the cutting.

  14. Fix the timber into position with a trigger clamp. Then, use your jigsaw with a timber blade, to carefully cut around the inside border of the star.

  15. Snowflake_step6

    Then, cut around the outside border of the star with your jigsaw.

  16. Snowflake_step7

    Use a detail sander to smooth the edges of your star.

  17. 9B6A3032

    You’ll need 12 pieces in total. Align the outside of the star with the corner of the plywood and draw around the inside of the star point. This will help you to draw cutter marks at the same length and width as the points of the star. Now align the star with the line you just drew. Repeat this 12 times.

  18. 9B6A3035

    Use your rule to mark straight lines at the end of each arm, as you see in this picture. Then cut out all 12 pieces using your jigsaw.

  19. 9B6A3037

    It’s time to fix the star and snowflake pieces to your frame.

  20. Snowflake_step8

    Use a pin hammer and pins to attach the pieces to the frame securely. Measure carefully with your ruler to make sure that the snowflake pieces are evenly spaced around the frame.

  21. 9B6A3065

    Now, it’s time to make the smaller star to add a decorative finish to the center piece. Using your compass, create a circle with a radius of 50mm and draw your star shape.

  22. Clamp the timber securely into position and carefully cut around the edges with your jigsaw.

  23. 9B6A3075

    Add the small star to the center of your snowflake with some wood glue.

  24. Snowflake_step9

    Paint the snowflake in a color of your choice, and you’ve finished!

View All Holiday DIY Projects